The two questions often asked together in an inquiry are really two separate things: “Can this chemical go in this drum?” is about material compatibility, answered by the SDS and compatibility tables; “Can this drum be shipped?” is about transport compliance, answered by the UN code on the drum. Handle them separately, or you risk getting both wrong. This article first explains the materials, then breaks down the UN code field by field.
1. HDPE and PP are not “more or less the same plastic”
Both are polyolefins and look similar, but they behave very differently under key conditions:
| Item | HDPE (high-density polyethylene) | PP (polypropylene) |
|---|---|---|
| Maximum continuous service temperature | Lower | Higher (can be used for warm liquids) |
| Low-temperature toughness | Stays tough at about −40 °C | Becomes brittle from about −18 °C; may shatter on impact |
| Stiffness | Medium, more flexible | Stiffer |
| Impact (dropping) | Better | Poorer |
| Oxidizing acids (concentrated sulfuric acid > 70%, chromic acid, nitric acid) | Weaker | Better |
| Dilute alkalis, hydrocarbons, alcohols, salts | Similar for both | Similar for both |
Two practical decision points: for cold stores, cold chains or outdoor stacking in winter, choose HDPE (PP shatters on impact at low temperature — it breaks rather than deforms); for warm liquids or oxidizing acids, choose PP.
One caution: “PP is solvent-resistant” overstates it. More precisely, PP resists stress cracking better than HDPE in some solvent environments, but prolonged solvent contact is not recommended for either. For solvents, confirm directly with the SDS and the container maker’s compatibility table rather than inferring from the material name.
2. Drums don’t “break” — they crack: environmental stress cracking
Most plastic container failures are not corrosion dissolving the wall but environmental stress cracking: residual stress (molding stress, cap torque, stacking load) acting together with certain chemicals (surfactants are especially notable) slowly produces fine cracks in the wall, until it leaks.
This also explains a common puzzle: why does a container leak when the compatibility table says “OK”? Because compatibility is never just “yes / no”; it is a combination of concentration, temperature and contact time. The same chemical may be fine at room temperature for a short time but not for long-term storage at high temperature.
The practical approach has three parts: start from the chemical’s SDS, check the concentration and temperature conditions against the container maker’s compatibility table, and before long-term storage, run a small-quantity real filling test.
3. How to read a UN code: UN 1H2/Y1.5/150 as an example
To ship dangerous goods, the drum must carry a UN marking. Taking the UN 1H2/Y1.5/150 on JIAHON’s 200 L blue flange drum, field by field:
| Field | Meaning | Explanation |
|---|---|---|
| 1 | Container type | Drum |
| H | Material | Plastic |
| 2 | Head type | Removable head (open-head); 1 is a non-removable head (closed-head) |
| Y | Performance level | Passed packing group II tests; can be used for packing groups II and III; X covers all three, Z only III |
| 1.5 | Maximum relative density of liquid | For liquids, the contents’ relative density must not exceed 1.5 |
| 150 | Hydraulic test pressure | In kPa; the internal pressure withstood in testing |
The full marking also continues with the last two digits of the year of manufacture, a country code and a manufacturer code, for tracing which year, country and maker produced it.
Remember one more pairing: for solids, the middle two fields change meaning — they become “maximum gross mass (kg)” followed by the letter S, instead of relative density and pressure. If you see /S, it is a solids marking and cannot be used for liquids.
4. Choosing closed-head (1H1) or open-head (1H2)
| Closed-head 1H1 | Open-head 1H2 | |
|---|---|---|
| Construction | Non-removable head, small openings only | Whole head removable, held by a locking ring |
| Use | Low-viscosity liquids, high sealing needed | Viscous materials, pastes, powders, whole-drum access or cleaning |
| Note | Hard to clean or empty completely | Sealing depends on ring torque and gasket; if the ring isn’t tightened to the specified value, the test conditions no longer hold |
The point most often overlooked when choosing open-head drums is the last one: the UN test covers the whole assembly — drum body, head, gasket, locking ring and the specified closing method. Swap in a lid that looks the same size, or don’t tighten the ring to the specified torque with a torque wrench, and the test conditions no longer hold.
5. Three common misunderstandings
- “A UN mark means it can hold any dangerous goods” — no. The UN marking is tied to packing group, maximum relative density and test pressure; outside these, it is not covered.
- “If the drum has a UN mark, the whole shipment is compliant” — the drum is only one part. Classification of the contents, UN number, labels and markings, inner packaging and absorbent, and transport documents must all be in place.
- “Lids of the same size are interchangeable” — see section 4; the test is done on the whole assembly.
6. Choosing from our existing specifications
Common capacities and types in JIAHON’s HDPE / PP industrial plastic drum series (sizes and accessories can be customized):
| Capacity | Shape | Material / color | Closure | Typical use |
|---|---|---|---|---|
| 1 L | Round | HDPE, black | Pull-off cap, wide mouth | Laboratories, reagent packaging |
| 4 L | Round | HDPE, black | Plastic swing handle, wide-mouth outer cap | General chemical use, tamper-evident cap design |
| 12 L | Round | PP, grass green | Standard lid | For water-based pressure-sensitive floor adhesive |
| 20 L | Square | HDPE, white translucent | Standard closure | Visible liquid level, food / chemical |
| 200 L | Round flange drum | HDPE, blue | UN-marked lid, metal handles | Dangerous goods transport (UN 1H2/Y1.5/150) |
The drum only solves “holding”; “storing” and “leaking” are two other questions: for storage quantities and cabinet planning for flammable liquids, see How to choose a flammable storage cabinet: calculate the regulated quantity first; for secondary containment on the floor of drum staging areas, use corrosion-resistant spill pallets, so leaks are caught rather than flowing into plant drains.
FAQ
Which is more chemical-resistant, HDPE or PP? It depends on the chemical. PP is better for oxidizing acids (concentrated sulfuric, chromic, nitric acid); the two are similar for dilute alkalis, hydrocarbons, alcohols and salts; prolonged solvent contact is not recommended for either. In practice, follow the SDS and the container maker’s compatibility table.
What does Y mean in a UN code? The performance level. Y means it passed packing group II tests and can be used for packing groups II and III; X can be used for all three, Z only for III.
Can an open-head drum hold liquids? Yes, provided that the open-head drum’s UN marking covers liquids (the marking shows a relative density and test pressure, not a gross mass with S), the locking ring is tightened to the specified torque, and the gasket is the one supplied with the drum.
If I’m not shipping dangerous goods, do I still need a UN-marked drum? Not necessarily. It isn’t mandatory for in-plant storage or general freight, but UN-marked drums have been through drop, stacking and leakproofness tests, so for high-value or leak-prone contents they are still worthwhile insurance.
To check material and UN specifications against your chemical’s properties, storage temperature and transport method, or for custom sizes, colors and printing, contact JIAHON or email [email protected]. Formal determinations of dangerous goods classification and transport documents should follow the authorities and carriers concerned.