中文English

Cleanroom Consumables Checklist: ISO Class Limits, Test Methods and Supplier Documents

Cleanroom Consumables: A Buyer’s Checklist by ISO Class, Test Method and Supplier Document

Cleanroom consumables are the items a cleanroom uses up and reorders on a regular cycle: garments and gloves, wipers and swabs, sticky mats, cleanroom paper and notebooks, ESD items, and clean packaging. In Taiwan they are often called 無塵室耗材; in mainland China, 洁净室耗材 or 无尘车间耗材. They differ from cleanroom equipment such as fan filter units (FFUs), pass boxes and air showers, which are capital items replaced every few years. Consumables are bought every month, across many SKUs, so many plants consolidate them into one list and reorder from a fixed set of suppliers.

This guide is for engineers and buyers setting up a new cleanroom, expanding a line, or taking over facility purchasing. It covers four steps: confirm the ISO class, choose items by category and test method, estimate monthly usage, and check what a supplier can document.

1. Start with the ISO 14644-1 class

Material and specification choices follow the air cleanliness class. ISO 14644-1:2015, Table 1, sets maximum concentrations (particles per m³, at or above the stated size):

ISO Class≥0.1 µm≥0.2 µm≥0.3 µm≥0.5 µm≥1 µm≥5 µmFED-STD-209E
5100,00023,70010,2003,520832see noteClass 100
61,000,000237,000102,00035,2008,320293Class 1,000
7———352,00083,2002,930Class 10,000
8———3,520,000832,00029,300Class 100,000

A dash means classification at that size is not applicable. For ISO 5 at 5 µm the standard notes sampling limitations and allows the macroparticle descriptor M instead. Sources: cleanroom.net (ISO 14644-1:2015 Table 1); FED-STD-209E equivalents, replaced by ISO 14644 in 2001, from Connect 2 Cleanrooms.

The limits follow the formula Cn = 10^N × (0.1/D)^2.08, where N is the class number and D the particle size in µm (Engineering ToolBox). Worked example: ISO 7 at 0.5 µm gives 10^7 × 0.2^2.08 ≈ 352,000 particles/m³, matching Table 1. When you send an RFQ, state the ISO class rather than a legacy name like “Class 10,000”. It leaves less room for misunderstanding.

2. The six categories and what to check

CategoryTypical itemsWhat to checkTest reference
Garments & PPEcoveralls, frocks, hoods, cleanroom shoes, shoe covers, masks, gloves, finger cotsclass, ESD requirement, size range, laundering cycleIEST-RP-CC003.5 (garments), IEST-RP-CC005.4 (gloves, finger cots)
Wipingdry and pre-saturated wipers, swabsfiber and particle release, sorbency, ions, NVRIEST-RP-CC004.3
Contamination controlsticky mats, tacky rollerslayer count, tack, change frequency, mat size vs. door widthproduct datasheet
Paper & stationerycleanroom copy paper, notebooks, pensshedding, duplex printing, writabilitydatasheet and test report
ESDgrounded worksurface mats, wrist straps, totes, traysresistance to ground, surface resistanceANSI/ESD S20.20
Packaging & handlingESD bags, EVA inserts, clean cartsbag type (antistatic, dissipative, shielding), sheddingANSI/ESD S20.20 and plant spec

3. Test methods behind the numbers

Wipers — IEST-RP-CC004.3. One wiper manufacturer publishes how its data maps to the RP (source): fibers ≥100 µm per cm² (Sec. 6.2.2.2), liquid-borne particles ≥0.5 µm per cm² by biaxial shake (Sec. 6.1.3), sorbent capacity and rate (Sec. 8.1/8.2, modified), non-volatile residue (Sec. 7.1.2) and metallic ions (Sec. 7.2.2). A second supplier’s wiper selection guide also uses IEST-RP-CC004 as its basis (source). Before comparing two wipers, check that both datasheets use the same method and unit. Per-wiper and per-cm² figures can’t be compared directly.

Gloves and finger cots — IEST-RP-CC005.4. It covers tensile, cut, abrasion, chemical resistance, barrier integrity, heat, ageing, outgassing and static charge, plus particle release (liquid agitation), extractables, NVR, bioburden and contact corrosion (Cleanroom Technology).

Garments — IEST-RP-CC003.5 (March 2023). It gives guidance on selecting, specifying, maintaining and testing cleanroom apparel. Appendix D covers test methods, and another appendix covers garment configurations by cleanliness class (Nimonik).

ESD items — ANSI/ESD S20.20. The wrist strap system must measure below 3.5×10⁷ Ω to ground, and worksurfaces and mobile equipment below 1×10⁹ Ω to ground (ESD Systems). For other limits, use the current edition of the standard.

4. Estimating monthly usage: an ISO 7 example

Formula: monthly usage = monthly entries × usage per entry × (1 + safety factor). Order quantity = monthly usage ÷ pack size, rounded up.

The figures below are hypothetical. Assumptions: ISO 7 assembly area, 30 people per shift, 2 shifts a day, 26 working days a month, which gives 1,560 entries a month. Two entrances, 20 wiping stations, 5 rework stations and a 10% safety factor.

ItemAssumed rateMonthly usageAssumed packOrder
Gloves3 pairs/entry≈5,148 pairs50 pairs/box103 boxes
Masks1.5/entry≈2,57450/box52 boxes
Disposable hoods1/entry≈1,716100/pack18 packs
Sticky mat layers4/entrance/day≈229 layers30 layers/mat8 mats
Wipers6/station/day≈3,432150/bag23 bags
Swabs20/rework station/day≈2,860100/bag29 bags
Cleanroom paper0.5 ream/day≈14.3 reams1 ream15 reams
Reusable coveralls3 sets/person, 5% replaced/month9 sets—9 sets (180-set pool)

Order from the table in month one, then compare it with what was actually used and adjust the per-entry rates. High-traffic entrances need more frequent mat changes.

5. Supplier evaluation: documents to request

  • COA (lot test report): measured particles, ions and NVR for the specific lot, so incoming inspection (IQC) can check every shipment.
  • TDS: typical values for material, size, basis weight, sorbency and surface resistance.
  • SDS: for pre-saturated IPA wipers, cleaners and other chemicals.
  • Particle and ion test reports: these state the method, such as IEST-RP-CC004.3, and the unit.
  • ESD resistance reports: results against ANSI/ESD S20.20 and your plant specification.
  • Lot traceability and packaging description: where the lot number is printed, number of bag layers, clean packing method.
  • Change notification policy: whether you are told before material, process or site changes.

A simple scorecard, each item rated 1–5 with weights adjusted to your plant: documentation 25%, test-method transparency 25%, catalog coverage 15%, lead time and replenishment stability 20%, response to nonconformance 15%. Run a one-month trial with IQC records before moving full volume.

6. Where these items are used

  • SMT lines: wipers around stencils and placement machines; ESD gloves and wrist straps for operators.
  • Cleanroom assembly: optics, displays and camera modules, with garments and wipers chosen by ISO class.
  • ESD protected areas (EPA): grounded mats, totes, trays and shielding bags checked against ANSI/ESD S20.20.
  • IQC: COA and TDS review, plus spot checks of resistance or particle data.
  • Assembly and test: swabs for fixture and connector contacts.

7. Common mistakes

  1. Writing “Class 10,000” instead of ISO 7 on the RFQ.
  2. Comparing wiper data measured by different methods or in different units.
  3. Comparing unit price instead of monthly usage. A wiper that absorbs more may mean fewer wipes per task.
  4. ESD mats and straps that pass on their own but are never properly grounded.
  5. No lot traceability, so a bad lot can’t be quarantined.

FAQ

How do I choose a cleanroom consumables supplier? Ask for COA, TDS, SDS, particle and ion reports and ESD resistance reports. Confirm the test methods behind them, for example IEST-RP-CC004.3 for wipers and IEST-RP-CC005.4 for gloves. Then score a trial lot using your IQC data.

Which ESD numbers should I check? Under ANSI/ESD S20.20, the wrist strap system should measure below 3.5×10⁷ Ω and worksurfaces below 1×10⁹ Ω to ground (source).

How often should consumables be reordered? It depends on headcount, shifts and class. Many plants review garments quarterly and reorder mats and wipers monthly, starting from the usage formula above.

Standards are cited for reference; use the current edition from each issuing body, and use the product datasheet for each item’s specifications. Acceptance of any process remains subject to your plant and customer specifications.

Back to top