中文

The Component Is Taller Than the Board — Where Should the Nozzle Pick? Lower and Upper Limits of Nozzle Tip Size

SMT placement · nozzle selection · for engineers. From placement force control and the coverage window to a suction force estimate: how to choose pick-and-place tooling for a stepped sub-board. JIAHON affiliated company engineering team · 7 September 2026 · about 9 minutes to read.

A 5.0 × 2.2 mm board only 0.254 mm thick, with a component in the centre standing 1.4 mm above the board surface, now has to be placed as a whole onto a mother board by an SMT placement machine. Pick the top of the component, or the bare areas on either side of the board? The answer is fixed by three things: whether the machine has placement force control, whether the nozzle tip has enough sealing area, and how much usable space the pick-up position tolerance eats. This article works through the three parts of SMT nozzle selection.

1. The problem: a small board that “walks”

This kind of part is increasingly common: it is itself a finished, populated small board (called a sub-board or module board), but at the next station it has to be placed onto a mother board as if it were a single “component”. The difficulty is its stepped shape — the board is thin, but the component in the middle rises more than five times the board thickness.

ItemValue
Board outline5.0 × 2.2 mm
Board thickness0.254 mm
Central component footprint2.0 × 1.2 mm (2012) or 1.6 × 0.8 mm (1608)
Component height above board1.400 mm
Bare area available on each sideabout 1.38 mm
Overall part height1.654 mm

Intuitively there are two options: pick the top of the central component, or pick the bare areas on both sides of the board. Which is right? Look at the machine first.

2. Start with the machine: force control decides where you can pick

Different generations of placement machines control the force applied to the part at the moment of pick and place in completely different ways. Newer models offer placement force control, usually requiring a force calibration station with a load cell and force-control nozzles so that parts are picked and placed at a set load. Many mid-range machines that have been on the line for years do not have this function — the force on the part at the moment of pick and place comes from only two things:

  • the compression of the spring built into the nozzle shaft
  • the Z-axis placement height setting

Picking the component top: stroke error has somewhere to go. The nozzle contacts the top of the component at a single point, with the spring directly above the pick point. Z-axis stroke error and height tolerance between parts are absorbed by the spring’s compression, and the force is not transferred to the 0.254 mm board.

Two-point bridge contact: stroke error has nowhere to go. If a gate-shaped nozzle straddles the component with its two legs landing on the bare areas, both legs make hard contact at once, and the thin board takes the force. On a machine without force control, any extra Z stroke has no component to absorb it, the force goes straight into the board, and the adjustable process window is clearly narrower.

The conclusion is clear: on a machine without force control, picking the component top comes first. A bridge nozzle can be made geometrically (fully checked in section 6), but it is a fallback, not the first choice.

3. Lower limit of tip size: too small and the pick is unstable

The tip’s effective sealing area directly determines suction force. Here we use a conservative criterion: vacuum of −20 kPa (allowing for leakage), 10 G acceleration and deceleration during pick and place, and a 5× safety margin.

ItemValue
Board volume, 5.0 × 2.2 × 0.254 mm2.79 mm³
Board weight (ceramic substrate estimated at 3.9 g/cm³)about 11 mg
Component volume, 2.0 × 1.2 × 1.4 mm3.36 mm³
Component weight (ceramic part estimated at 6.0 g/cm³)about 20 mg
Total part weight (about 22 mg with a 1608 component)about 31 mg = 0.031 gf

Putting the total weight into the criterion (part weight × 10 G × 5 margin ÷ vacuum), the sealing area needed is 0.76 mm² for a 2012 component and 0.53 mm² for a 1608 component. This is the lower limit of tip size.

Tip: nozzles are consumables, and tip flatness deteriorates with hours of use. Once the tip wears a rounded edge or a chip, the same vacuum no longer gives the same force, and the pick-up reject rate is the first sign. Regular replacement costs less than chasing yield afterwards. See JIAHON: SMT nozzles by machine brand.

4. Upper limit of tip size: the space taken by pick-up tolerance

The upper limit comes from the other direction: even with an unfavorable pick-up position offset, the tip must stay entirely within the component top. Once the tip overhangs the component edge, that part becomes a leak path. With the component’s short side W and a one-sided pick-up offset e:

Usable tip width ≤ W − 2e

One-sided pick-up offset e2012 (short side 1.2 mm)1608 (short side 0.8 mm)
0.05 mm1.10 mm0.70 mm
0.10 mm1.00 mm0.60 mm
0.15 mm0.90 mm0.50 mm

e combines the positioning accuracy of the feeding container and the machine’s pick-up accuracy — tape pockets, tray cavities and machine condition all count — and must be taken from actual site conditions.

From this table, the common φ1.0 mm tip exactly equals the upper limit for a 2012 component at e = 0.10 mm.

5. Round vs oval tips: taking back the space along the long side

A round tip wastes space by design: its diameter is fixed by the component’s short side, and the space along the long side goes unused. An oval (racetrack) tip takes that space back.

Item2012 component1608 component
Component top2.0 × 1.2 mm1.6 × 0.8 mm
Usable area after offset1.8 × 1.0 mm1.4 × 0.6 mm
Lower limit: sealing area needed0.76 mm²0.53 mm²
Round tip at upper limit — sealing area / marginφ1.0 mm (a standard size exists): 0.79 mm² / 5.2× — just passesφ0.6 mm (smaller than the nearest standard size): 0.28 mm² / 2.7× — fails
Custom oval tip — sealing area / margin1.8 × 1.0 mm: 1.59 mm² / 10.4×1.4 × 0.6 mm: 0.76 mm² / 7.2×
Area increase2.0×2.7×

Margins are calculated at −20 kPa vacuum including 10 G acceleration, against a 5× criterion. If the machine’s actual vacuum is stronger than −20 kPa, the margin rises in proportion.

On the same machine with the same board, changing the component from 2012 to 1608 reverses the conclusion. For 2012, a standard round tip gives 5.2× and just passes; for 1608, the round tip’s upper limit is only φ0.6 mm, smaller than the nearest standard size, and the margin falls to 2.7×. Here a custom oval tip is not just “better” — it is the approach that meets both the lower and the upper limit.

Note: oval tips are not an exception. The machine makers’ standard nozzle ranges already include oval-tip models (for example the 0.7 × 0.4 mm class), though the size may not match your part exactly. A custom tip adjusts the size of an existing standard type rather than inventing a new one. See JIAHON: nozzles for JUKI placement machines | nozzles for Panasonic placement machines | nozzles for YAMAHA placement machines | nozzles for FUJI placement machines. JIAHON is not the authorized distributor of JUKI, Panasonic, YAMAHA or FUJI in Taiwan.

6. Four possible routes, and the cost of each

Option A | Pick the component top (first choice). The pick point coincides with the part’s center of gravity, and single-point suction creates no tipping moment; the component top is also the one single flat surface on the whole part, so sealing is simple. The risk lies in the component top itself — resistor and capacitor tops are usually flat, but inductors and filter components often have raised features or laser marking that cause leaks.

Option B | Bridge nozzle with two suction pads (geometrically possible, but depends on the machine). A gate-shaped nozzle straddles the component, with each leg picking one bare area. Taking a component zone width of 2.24 mm (= 5.0 − 1.38 × 2) as the unfavorable case, the geometry is:

Geometry itemValueBasis
Clearance under the bridge0.2 mmGap above the 1.4 mm component
Leg length1.6 mm1.4 mm + 0.2 mm clearance
Inner span between legs2.8 mmComponent width 2.24 mm + 0.27 mm clearance each side
Leg width1.0 mmWithin the 1.38 mm bare area
Outer edge of legs2.4 mm from centerBoard half-width is 2.5 mm; legs stay within the board outline

The last row matters: with both legs entirely within the board’s outline, laser centering still sees only the part itself and does not count the nozzle legs as part of its width. This is easy to overlook when designing a bridge nozzle, and a common source of problems.

Option C | Soft foam tip. Foam cut to the part’s outline and thicker than the component’s height is pressed down so it wraps the component and seals on the board surface on both sides. The advantage is that it is not fussy about shape; the cost is that foam is a consumable material that sheds particles with use. For products with high cleanliness requirements (RF components, optics, medical electronics), check first whether this is acceptable.

Option D | Gripper nozzle. Mechanical gripping replaces vacuum, so the upper and lower limits on tip coverage disappear, and the raised central component does not matter. There are two constraints: the gripper must enter from both sides of the part, so the feeding container must leave side clearance; and the thin board must be able to withstand the gripping contact.

Warning: one route does not work — picking only one bare area on one side. The center of the bare area is about 1.8 mm from the part’s center of gravity, while the part’s half-length is only 2.5 mm, so the pick point is about 72% off center. After pick-up the part tilts about the nozzle, the profile measured by laser centering is distorted, and placement accuracy drops. To use the bare areas, both must be picked at once — that is, option B.

7. Before going on the machine, check these five things

What to checkWhy it matters
The actual component part number, and whether its top is flatThe short side sets the tip’s upper limit; raised features or marking on the top break the seal
Whether the “bare areas” marked on the board are pads or holesA hole cannot hold vacuum, so the landing point must be specified elsewhere
Whether the machine uses laser or vision centeringA stepped outline relies on laser profile scanning; the centering method affects the process window
The measured vacuum at pick-upNozzle number and vacuum are parameters in the production program; non-standard shapes usually need manual entry
Feeding method and pick-up position offsetOffset e sets the tip’s upper limit; clearance in the container also limits the nozzle’s outer diameter

Tip: a clogged or contaminated nozzle invalidates all the calculations above. Flux volatiles, paste residue and board debris build up on the tip and in the bore, the actual vacuum falls well below the setting, and the symptom is a pick-up reject rate that rises for no apparent reason. Making nozzle cleaning part of scheduled maintenance works better than adjusting the Z axis every time. See JIAHON: SMT / PCBA cleaning equipment and inspection | electric stencil cleaning machine JHPBT-1000X.

8. Quick selection guide

SituationSuggestion
Machine without force controlPick the component top first, letting the nozzle spring absorb Z stroke error
Flat component top, short side ≥ 1.2 mmVerify first with the machine maker’s standard round tip; switch to a custom tip if vacuum is low
Component short side ≤ 0.8 mmRound tips usually lack coverage area; evaluate a custom oval tip directly
Component top uneven or cannot take loadMove to option B, the bridge nozzle, but confirm the machine’s placement force can be controlled
Very irregular shape, relaxed cleanlinessOption C, foam tip, faster to develop
Feeding method leaves side clearanceOption D, gripper, which avoids the vacuum sealing problem entirely

If the nozzle doesn’t fit, you don’t necessarily need a new machine

JIAHON supplies nozzles and related consumables for placement machines from Panasonic, YAMAHA, FUJI, JUKI and other major brands, and takes on the design and manufacture of custom tips. Give us the actual part to be picked and we can start evaluating and making samples — you don’t need drawings first. Related product: custom nozzles (special-shaped nozzles). Contact JIAHON engineering or email [email protected].

The part dimensions and calculation conditions in this article are a case set up to explain the selection logic and are not the actual specifications of any customer’s product. Densities, acceleration and vacuum values are engineering assumptions; in practice, recalculate with measured site values. Individual cases vary.

JIAHON affiliated company engineering department. Copyright in the calculations, figures and framework of this article belongs to the JIAHON affiliated companies; you are welcome to quote or republish it with attribution and a link to this page.

Back to top