Acrylic does not break at the first touch of alcohol, and it is not always fine after wiping either. Whether it clouds or develops fine cracks depends mainly on three conditions: the alcohol concentration and the contact time; whether this sheet is under stress (bent, machined, or at screw points); and whether it is an extruded sheet or a cast sheet. Sheet makers’ chemical-resistance tables list 95% and absolute alcohol as “not resistant,” and low to medium concentrations are mostly “limited resistance”; the makers do not all say the same thing. When you are not sure, mild detergent and a soft cloth are the safe choice.
Figure 1: Judgment flow before wiping.
Table 1: What you see, and the usual cause
| What you see | Common cause | How to confirm, and the next step | Basis |
|---|---|---|---|
| Whitening after wiping that fades or disappears once washed and dried | A temporary surface effect, or cleaner residue or water marks left unwiped | Wash, dry with a soft cloth, and look again; if it disappears, it belongs to this type | A, B |
| A haze that does not wipe off, with dense fine lines when viewed from another angle | Fine cracks caused by solvent (crazing); the fine lines scatter light and look like haze | This is damage to the material, not dirt; do not use the same cleaner on that spot again | A, E |
| Fine lines concentrated at hole edges, bends, screw points, machined edges, or glued joints | Stress at that spot, then exposure to solvent | Check against the stress check in Figure 1; the makers list bending, thermoforming, screen printing, gluing, and machining as sources of stress | A, F |
| Surface turns soft, tacky, swollen, discolored, or blistered | The solvent has attacked the material (the “not resistant” behavior in the makers’ tables) | Stop using that cleaner at once and wash it off | A |
| Fine lines grow longer and actual cracks appear | Crazing is a precursor to cracking; continued stress and solvent action lead onward | Once cracked it cannot be restored by cleaning; replace the part or ask the sheet supplier to assess | G |
| Haze or fine lines appear without alcohol | Other cleaners (such as glass-cleaning spray), paint or glue, stress from water absorption, or scratches from dry wiping | Go back and check the cleaners and glues used recently; dry wiping and cloths carrying grit make the surface lose clarity | A, B |
| It picks up dust again soon after wiping | Acrylic readily generates static when wiped and attracts dust | Use the anti-static cleaner supplied by the sheet supplier | A, E |
Table 2: Tolerance of acrylic to common cleaners (just the cells with a data source are listed)
| Cleaner or method | What the makers’ data says | Conditions and reminders | Basis |
|---|---|---|---|
| 1. Mild soap or detergent + lukewarm water + soft cloth | Listed as a recommended method by several makers | Rinse, then dry with a soft cloth; do not dry-wipe, do not use paper towels, do not scrub | A, B, C |
| 2. Isopropanol (IPA), low concentration | Both chemical-resistance tables list “limited resistance”; one cleaning page lists “diluted to 30%” as an option | One table says it applies up to 50%; the other gives no concentration | A, B |
| 3. Isopropanol (IPA), 95% and above (including 99%) | The data sheets we checked have no direct data | The IPA Jiahon sells is marked 99% and above; before using it on acrylic, follow the sheet supplier’s advice | H |
| 4. Ethanol (alcohol), low concentration | One table: resistant up to 15%, limited resistance at 15–30%; the other table: limited resistance at 50% | These are tests on unstressed flat sheet at room temperature | A, B |
| 5. Ethanol (alcohol), about 60–75% (common for disinfection) | Two makers’ cleaning instructions say it can be used (wipes of 70% and above; disinfectant of 60% and above, the latter for cross-linked cast sheet); the chemical-resistance tables above have no data point in this range | One stresses that the result depends on concentration, contact time, temperature, and internal stress; rinse and dry after wiping | B, C |
| 6. Ethanol (alcohol), 95%, absolute | One table lists “not resistant” (absolute); the other lists “not resistant” (95%) | The two tables agree | A, B |
| 7. Strong solvents such as acetone, gasoline, benzene; glass-cleaning spray; ammonia-containing cleaners | Listed as not to be used | Strong solvents can make fine cracks appear on the surface and soften it | A, B, E |
| 8. Oil and glue marks: hexane, aliphatic naphtha, kerosene | The maker and the conservation institute both mention use on oil and tar | Flammable; use carefully in a ventilated place and follow the sheet supplier’s advice | A, E |
| 9. The sheet supplier’s anti-static cleaner | The maker recommends it for removing static from acrylic surfaces | Products differ by supplier; follow their instructions | A, E |
| 10. ESD acrylic (anti-static surface coating, cast base) | One data sheet says “IPA cleaning recommended,” and its test table lists IPA as “no change” | This is the data for that product; it cannot be extended to other ESD sheets | D |
The definition of “limited resistance” differs by source: one writes “can withstand it at room temperature for a short time; whether it applies is for you to judge,” and another writes “a temporary effect that can be wiped off again.”
1. Why clouding and crazing happen
When a solvent touches acrylic, the damage is often not that the whole sheet dissolves, but that extremely fine cracks first grow at the stressed positions, called crazing. When the fine lines are dense, they scatter light and look like haze (this is a general explanation). The literature treats crazing as a precursor to cracking, so once fine lines appear they are not dirt that can be wiped away and recovered.
Stress has two sources. One is stress left in the sheet during processing: the makers list bending, thermoforming, screen printing, gluing, and machining. The other is applied in use, for example tightened screws, clamping, or being held bent. The ASTM F484 test method puts a test piece under bending stress in contact with the liquid to be tested, then looks for crazing.
2. The three conditions
Condition 1: Concentration and contact time. For the same alcohol, the higher the concentration, the worse the rating in the makers’ tables (Table 2, rows 4–6). The makers also warn that temperature, mechanical stress, and higher concentration make the effect more severe, and that contact time matters too. “Limited resistance” in the tables is from tests on unstressed flat sheet at room temperature; a sheet in the field is warmer and stressed, so take it conservatively. “A single wipe” and “liquid pooled in a seam, soaking” are two different things.
Condition 2: Whether there is stress. The maker points out that internal stress lets solvent cause crazing, and that annealing can reduce it to a lower level. For stressed parts, you can ask the sheet supplier to assess annealing; temperature and time depend on thickness and grade, so follow the supplier’s advice.
Condition 3: Extruded or cast sheet. Both makers point out that cast sheet is more resistant than extruded sheet: one writes that cast sheet is more resistant to stress crazing, and the other writes that extruded sheet is more easily dissolved by solvent. If you cannot tell which one you have, confirm with the supplier; do not guess from appearance.
Where the statements differ. One care instruction lists “alcohol” among the things not to use, while the same maker’s cleaning page lists IPA diluted to 30%; one maker says wipes of 70% and above can be used, and another says disinfectant of 60% and above can be used (for cross-linked sheet); yet both chemical-resistance tables list 95% or absolute alcohol as not resistant. The differences may come from sheet grade, test conditions, and purpose (cleaning, disinfecting), and the data themselves do not explain each one, so this is the general case and individual cases still have to be judged on their own.
3. Acrylic parts common in a plant, and how to judge them
Dust covers and cleanroom bench shields: a large flat panel lying flat has a different stress state from corners bent into a cover shape, screw holes, and edges held in a frame. Avoid alcohol on the latter first.
Fixtures: machined edges, hole positions, and screw points are all on the list of stress sources; use mild detergent as the main method, and for glue marks and oil follow the sheet supplier’s advice.
Display panels and window covers: if the surface has a coating or film, the effect of alcohol on the coating is outside what this article checked; follow the panel supplier’s advice.
Electrostatic protection (ESD) sheets: anti-static treatments differ by maker. Some data sheets state IPA can be used and some do not; go by that sheet’s data sheet, and ask the supplier if there is none.
4. When not using alcohol, what to use instead
The makers and the conservation institute follow very similar practices:
Mild soap or detergent with lukewarm water, scrubbed gently with a soft (microfiber) cloth, then rinsed and dried to avoid water marks.
Do not dry-wipe, since dust and grit scratch the surface; do not use paper towels; do not scrub with a brush or use a scraper.
Do not leave cleaner on the sheet, and do not clean in direct sunlight or high heat.
If it picks up dust again after wiping, that is static; use the sheet supplier’s anti-static cleaner.
Oil and glue marks: Table 2, row 8, and follow the sheet supplier’s advice.
Where no basis could be found (for example special coatings or special grades), we always write “follow the sheet supplier’s advice.”
5. If the material is confirmed to tolerate it, how to supply and handle it
The above is about judging whether to use it. If your sheet’s data sheet allows it, or what you are wiping is not an acrylic part, you need alcohol and handling tools; Jiahon offers the following items, with specifications as on the product pages:
Related products mentioned in this article (specifications as on each product page; actual configuration, price, and lead time by inquiry):
Industrial Alcohol Series (75% / 95% / IPA): the product page lists 75% cleaning alcohol (500 ml, 4 L, 20 L), 95% alcohol (20 L), 95% ethanol (denatured and undenatured, 4 L each), and IPA isopropanol (4 L, marked 99% and above). Check Table 2 before choosing a concentration; price and availability on the product page or by inquiry.
Alcohol Pump Bottle: PP plastic graduated bottles (the specification table lists 100 / 200 / 250 / 500 ml) and glass graduated bottles (120 / 180 ml), with plum-blossom and anti-splash dispensing heads. They allow metered dispensing and a small amount to dampen a wiping cloth, so that liquid does not pool on the sheet.
Cleanroom Wipes: the product page lists polyester model 3008 and microfiber models 3002 and 4009, among others, with sizes. The product page does not state use on acrylic, so test first on an inconspicuous spot.
How to Read Cleanroom Wipe Specifications: a specification page explaining the differences between models 3002 / 3008 / 4009, the edge sealing methods, and how to read the two figures LPC and NVR; the page does not state use on acrylic.
Explosion-Proof / Fire-Safety Cabinet (chemical safety cabinet): the page describes an explosion-proof safety cabinet for storing flammable liquids, with nine capacities listed from 4 to 115 gallons, and uses that include the electronics manufacturing industry (IPA / solvents); capacity and configuration by inquiry.
Safety reminder: alcohol and IPA are both flammable liquids. Keep them away from flames, sparks, and electrical equipment, store them sealed in a cool, ventilated place, and do not use them in an enclosed space.
Further reading
To read through the related process steps together, continue with these:
What cleanroom consumables are there? Six categories, uses, and a purchasing list at a glance
What drum for chemicals? How HDPE and PP differ, and what the code UN 1H2/Y1.5/150 means
Sources
This article is compiled from: A = chemical-resistance table and cleaning and care instructions of an acrylic sheet maker; B = chemical-resistance table and cleaning guide of another cast acrylic maker; C = technical data sheet of cross-linked cast acrylic; D = data sheet of an ESD acrylic; E = technical document on cleaning glass and acrylic display cases from a Canadian government conservation institute; F = ASTM F484 (test method for stress crazing of acrylic); G = literature on environmental crazing of polymers (including a NASA technical report); H = Jiahon product pages.
Standards and references. The standards cited in this article should be taken in the current edition of each issuing body.
ASTM F484, Standard Test Method for Stress Crazing of Acrylic Plastics in Contact with Liquid or Semi-Liquid Compounds. Issuing body: ASTM International.
CCI Notes, Cleaning Glass and Acrylic Display Cases. Issuing body: Canadian Conservation Institute.
NASA technical report, Environmental stress cracking of polymers (1980). Issuing body: NASA (Technical Reports Server).
Environmental Crazing of Polymethylmethacrylate and Polycarbonate (academic literature record). Issuing body: the Italian National Research Council (CNR) institutional repository.
This article is a general compilation of information. The actual tolerance of acrylic varies with sheet grade, concentration, contact time, temperature, and stress; this is the general case, and individual cases still have to be judged on their own. For important parts, go by the sheet supplier’s data sheet and your own process specification.