中文

How to Choose PCB Support for Solder Paste Printers: 4 Board Conditions Compared for DEK and MPM

You don’t always need vacuum blocks, but during solder paste printing the PCB must always have support underneath that holds it up without pressing on bottom-side components. For single-sided boards, or the first side of double-sided boards, where the underside is flat, flat support blocks or well-placed tooling pins are enough; for the second side of double-sided boards, thin boards, flex boards or warped boards — where the underside has components or the board isn’t flat — use dedicated tooling cut out around bottom-side components, adding vacuum if needed. The brand isn’t the deciding factor; the deciding factor is whether paste is squeezed under the stencil after printing and whether paste volume is consistent board to board.

Table 1 | Support methods by board condition

Board conditionRecommended supportReasonSources
Single-sided, or first side of double-sided (no bottom-side components)Flat support blocks, magnetic blocks or manually placed tooling pins, supporting the whole undersideA maker’s technical article lists flat plates and magnetic blocks as the preferred approach here; DEK positions its Support Bars as simple general support for single-sided PCBs only[1][2]
Second side of double-sided (first-side components soldered, facing down)Dedicated tooling cut out around bottom-side components, or supports that adjust to component heights and lock; ordinary pins only in component-free spotsBottom-side components limit pin positions; a DEK applications manager notes these pins are often the root cause of double-sided defects[1][3][9]
Warped boards (bow and twist)Flatten first, then fix: top clamping or side clamps, with bottom vacuum or dedicated tooling; conformal supports are limited on severe warpageIf the board doesn’t seal against the stencil, filling is poor, release uneven, and bridging possible[3][4][5]
Thin and flex boardsDedicated tooling plus vacuum; very small, soft or irregular boards can use carriersDEK data say thin, flexible and warp-prone substrates are fixed by vacuum; boards in carriers may still move slightly[2][4][10]

Table 2 | Four support methods compared

MethodHow it supportsUseWatch out forJIAHON products
Vacuum blocks / vacuum toolingTooling surface contacts the board underside, and vacuum pulls it flat [4][10]Thin, flex and warp-prone boards [4][10]Too much vacuum can pull thin boards into recesses, with one case of insufficient paste on large apertures [6]; each product needs matching tooling [2]Not currently on product pages; please ask
Hard support blocks / pinsMagnetically fixed to the worktable, placed manually under the board [1][3]Single-sided and first side of double-sided boards [1][2]A missing or misplaced pin increases paste volume scatter and may press on bottom-side parts [1][3]; placement depends on operators [3]Support blocks and tooling pins for DEK printers
Soft pinsSoft rubber tips support the underside without leaving marks (per our product page); conformal systems also use soft caps [1][2]Boards whose undersides must not be scratched or marked (per our product page)No public data found on when soft pins are enough; verify by trial printing; pin height must suit the worktable (per product page)Soft pins with magnetic base for DEK; soft pin set
Dedicated toolingA support plate made for the product, cut out around bottom-side components and contacting the rest [3][10]Second side of double-sided boards, dense bottom-side components, long-running fixed products [1][9]Needs design and lead time, hard to modify, one per line, and version control [1][3]No such product page; please ask

Why the PCB always needs support during printing

The squeegee presses down and pushes forward, putting downward force on the board. The thinner and larger the board, the more unsupported area underneath, and the more easily it bends [1].

Once the board bends, the seal between pads and stencil apertures breaks, paste seeps under the stencil, and bridges form that become shorts after reflow [1][3][5].

Support itself can go wrong. A missing or misplaced pin changes board stiffness and increases paste volume scatter; one source notes this may not be visible after printing and only shows as defects after reflow [3]. A pin pressing on a bottom-side component damages it directly and tilts the board relative to the stencil [1][3]. So there is one principle: support firmly, and only where support belongs.

Check the board condition first, then decide on vacuum

Second side of double-sided boards

This is the condition most prone to trouble. First-side components now face down, so pins can only go in the gaps; where gaps are too few, some areas go unsupported. Makers’ data recommend dedicated tooling (cut out around bottom-side components) or supports that adjust to component heights and lock [1][9].

Pins aren’t ruled out. One source tested a double-sided 4-up panel and found no significant difference in paste volume, height, area or offset between 76 pins and a dedicated support plate — but for one board type only [3]; another application note lists recessed vacuum tooling as the preferred approach and magnetic pins as less desirable but sometimes unavoidable [4]. The two conclusions differ; there is no universal ranking, so let your own trial print data decide.

Warped boards

Measure before deciding. A rule of thumb from one maker’s column: for a 100 mm square board, if a 1 mm shim fits under the board anywhere, strong top clamping is needed and side clamps alone may not hold it [5]. This is a single source’s rule of thumb — use it as initial screening, not a specification. With severe warpage, even locked conformal supports struggle to correct it [3]; the option is to flatten first, then fix with vacuum or dedicated tooling [4][5].

Thin and flex boards

Makers’ data put thin, flexible and warp-prone substrates under “dedicated tooling plus vacuum” [10]; very small or irregular boards use carriers, though boards may still move slightly within them [2][4]. More vacuum isn’t always better: in one case with a board about 0.4 mm thick, vacuum pulled the board into a tooling recess and the leading edge of large apertures lacked paste; reducing vacuum flow, with all else unchanged, fixed it [6]. That’s a single case, but a reminder: when you change vacuum tooling, adjust the flow too.

What DEK and MPM call things, and how they do them

None of the makers’ public data we found say vacuum is required for all boards; it appears as an option for thin, flex and warp-prone boards. Both brands are summarized in the same four categories.

DEK

  • Standard support: Tooling Pins supplied with the machine, placed manually [3][6]; Support Bars, simple general support for single-sided boards, placed by hand between the rails [2].
  • Conformal support: Grid-Lok, pneumatic pins that conform to the board underside and then lock [2].
  • Dedicated tooling and vacuum: Custom Dedicated Tooling, with vacuum added for thin, flexible and warp-prone boards [10].
  • Clamping: edge clamps or top clamps hold the board edges; with thin boards or fine-pitch parts near the edge, top clamps may stop the board sealing against the stencil [7].

MPM

  • Standard support: magnetically fixed, manually placed pins; the maker’s technical article describes them as flexible but needing correct placement [1].
  • Conformal support: Gel-Flex, polyurethane gel sealed in a membrane on magnetic bases, gentler on bottom-side components [11].
  • Dedicated tooling and vacuum: no public maker data with an MPM-specific name were found; industry sources use the generic term vacuum tooling [4].
  • Clamping: EdgeLoc II side clamps (Edison models), with no top clamps — the board edge is flattened first, then clamped from the sides [8].

What happens when support is wrong: 5 common symptoms

  • Paste volume varies. A missing pin or different placement changes board stiffness [3].
  • Bridging, paste on the stencil underside. The board bends, the seal breaks and paste seeps under the stencil [1][5]; for stencil underside cleaning, see Is your stencil cleaning done right?
  • High or unstable paste volume near the board edge. Top clamps or edge clamps leave a gap at the edge [4][7][8].
  • Insufficient paste at the leading edge of large apertures. A thin board is pulled into a tooling recess by vacuum [6].
  • Print offset. The board moves after alignment and defects follow [5]; worn, loose edge clamps are a common cause — see How to troubleshoot solder paste printing defects.

How to place support: 5 practices

  • Judge the board condition first. Warpage, bottom-side components and thickness decide which row of Table 1 applies.
  • Keep support points off bottom-side components. Place pins only in component-free spots; too few spots signals a change to dedicated tooling or adjustable supports [1][3][9].
  • Save the placement as a picture. Photograph or draw the positions and follow them at changeover. Pin setup depends on operators and is easily short of pins [3]; training and setup rules are needed for repeatability [9].
  • Look at clamping and support together. Worn or loose edge clamps let the board shift, causing offset and opens. JIAHON offers compatible edge clamps for DEK printers; please ask.
  • Measure the first board after changing support. When differences aren’t visible, look at SPI volume and height scatter [3]; with vacuum tooling, start at low flow.

Are soft pins enough?

Soft pins are support pins with soft rubber tips. Our product page says they give even underside support without marking or scratching the PCB. Conformal system pins also often have soft caps; Grid-Lok spares include ESD rubber caps [1][2].

As for when soft pins are enough, we checked makers’ and magazine sources and found no threshold for board thickness or warpage. What you can do: keep the same placement, switch to soft pins and compare first-board SPI volume and height scatter; if it doesn’t worsen, keep them.

Two reminders: pin height must suit the worktable (our product page states pin height must match the model’s support platform clearance); and the “SMT soft pin set” product page describes use in placement, so for use on a printer, please ask to confirm size and fit first.

Related JIAHON parts

Specifications are from our product pages; please ask about anything not listed. The same part number may be supplied in different forms depending on stock (including compatible versions); say which you need when inquiring.

To confirm fit, please contact JIAHON or email [email protected] with the machine model, board thickness, board size and a photo of the bottom-side components.

Further reading: How to troubleshoot solder paste printing defects; Is your stencil cleaning done right?; Wiper paper specs across printer brands; White-light structured light measurement of warpage and thickness

References

[1] Z-axis PCB support options, magazine column, 2006. [2] DEK PCB support solutions, DEK product page. [3] Dedicated vs. flexible underboard support, magazine column, 2019. [4] Solder paste printer process parameters, application note, 2017. [5] Flatness is a must, magazine column, 2019. [6] Printers and peas, magazine column, 2023. [7] Precise positioning in tooling nests, magazine column, 2009. [8] EdgeLoc board edge clamping, MPM product release, 2019. [9] Double-sided SMT soldering Q&A, expert Q&A, 2007. [10] DEK custom dedicated tooling, DEK product page. [11] MPM Gel-Flex, MPM product release, 2003–2004.

This is a general overview; actual practice depends on your machine, board material and process. Cases and rules of thumb each come from a single source; verify by trial printing and measurement before fixing a method. DEK, MPM and the product and model names mentioned are trademarks of their respective owners. JIAHON is not the authorized distributor of DEK or MPM in Taiwan; compatible parts are made to the machine makers’ part numbers.

Back to top