SMT mounter technical Q&A · notes on learning programming
The quicker way to learn mounter programming is not to memorize screens, but to imagine yourself as a machine that knows nothing. In its whole life it does one thing: carry a part from point A (the feeder) to point B (a given place on the PCB). Every field on the screen answers one question the machine cannot answer itself, eight in all. This article uses the Yamaha YSM20R as the example: it goes through the eight questions first, then grows out one question at a time.
Jiahon affiliated company, Engineering Department · SMT mounter technical file
Engineers who have just taken over a mounter often get stuck in the same place: there are many screens and many parameters, every word is understandable, yet they do not connect. Manuals are mostly arranged by function or by course order — first get to know the machine, then create parts, set up the board, teach coordinates — and following them lets you build a program, but when you change the board or the machine you must start over.
We learn a machine another way: pretend to be the machine, knowing nothing. Then every setting has a “why” — because it does not know, we have to tell it. Once the question is right, you can naturally find which screen holds the answer.

Figure 1. Imagine yourself as a mounter. A part goes from point A (feeder) to point B (PCB). The machine first has to know point B (① ② ③), then pick the part from point A (④ ⑤ ⑥), then place it at point B (⑦ ⑧).
Jiahon does not sell mounters. What we make is what surrounds the mounter: nozzles, feeder parts, supports and fixtures, so we care about “why the machine is set this way” — behind each setting there is a dimension that a peripheral part must keep.
First, a word on sources: the YSM20R specifications in this article are quoted from public information on Yamaha’s website (viewed 2026-09-30). The operating logic is the Jiahon Engineering Department’s own summary of learning the machine, plus field experience, written in our own words; it does not quote or reproduce the text, pictures or steps of the maker’s manual. For screen names and actual operation, follow the maker’s manual and the maker’s training. The YSM20R is already listed as a discontinued model on the website, but discontinued does not mean offline: machines are still running, so someone still has to look after their programs and parts.
There are twelve questions below: the first covers the main line; the second to the eighth are the details of the eight questions; the last four grow off the main line — running fast, tray parts, what to check first when something goes wrong, and what to prepare if you want peripheral parts made.
Questions in this article
Learning mounter programming: which main line should you grasp first?
How big is the board, how wide do you open the rails, where does it stop, how is it fixed?
Why must fiducial marks be on the diagonal? What does each of the three levels cover?
Where is point A? Feeder station number and feeders
The machine does not know what this is: what must part data tell it? How do you choose a nozzle?
How does the machine’s eye recognize a part? Why is XY measured on every part, while Z relies on consistency?
Where to place: where do X, Y and R come from? Why should the part follow the solder paste?
How fast, how slow: which speed, dwell, height and vacuum threshold settings do you adjust?
The catalog says 95,000 CPH; where does the cycle time on site come from?
When point A is a tray, what needs extra attention?
Misplaced, or thrown away: which question do you check first?
If you want Jiahon to make nozzles, supports or trays, what data should you prepare?
Q 01. Learning mounter programming: which main line should you grasp first?
One is enough: the part goes from point A (feeder) to point B (a position on the PCB). The order: first get to know point B — how big the board is, how it is fixed, how far it is skewed; then pick the part from point A — where to pick, what it is, whether it was picked straight; then place it at point B — where to put it, how fast and how slow. Eight questions in all.
Why get to know point B first? Because point B is on the board. If the board has not come in, is not clamped firmly, or is not aligned, the machine cannot even work out “where to place”. So the first three questions all ask about the board; once the board is settled, it is the part’s turn.
Table 1. Eight things the machine does not know, and what we tell it
| # | What the machine does not know | What we tell it | Roughly where in the YSM20R program | In this article |
|---|---|---|---|---|
| ① | How big is the board? | Board length, width, thickness | Board | Q02 |
| ② | How wide are the rails? Where does it stop? How is it fixed? | Rails set to board width; the stopper stops it; the board edge is clamped, support pins push from below, a hold-down presses from above | Board | Q02 |
| ③ | How far is the board skewed? | Fiducial marks: whole board (diagonal), panel block, special or high-value ICs | Mark, Board | Q03 |
| ④ | Where to pick? | Feeder station number, that is, point A | Parts | Q04 |
| ⑤ | What is this thing? | Length, width, height; for leaded parts also lead count, pitch, lead width; type, nozzle, package | Parts | Q05 |
| ⑥ | Is it really that part? Was it picked straight? | Recognize with the camera; measure the part’s offset and angle on the nozzle | Parts | Q06 |
| ⑦ | Where to place it? | X, Y coordinates and angle R, confirmed by teaching points with the camera | Board (placement coordinates) | Q07 |
| ⑧ | How fast, how slow? | Speed of picking and placing, dwell time, height, vacuum judgement | Parts | Q08 |
“Roughly where in the program” is Jiahon’s mapping to the YSM20R’s screen tabs; models and software versions differ, so go by the real machine. Other brands use different names, but the eight questions do not change.
This table is also a way to read a program. When you get a program someone else wrote, do not start from the first field; ask first: how does it answer each of the eight questions? The question it cannot answer, or answers inconsistently, is usually where the problem is.
To see where the mounter sits in the whole line and what comes before and after it, read How does an SMT line really work? Printing, placement, reflow and quality control in one article; for which consumables a new SMT line needs, see Setting up a new SMT line: what to stock? A full consumables checklist for engineers.
Q 02. How big is the board, how wide do you open the rails, where does it stop, how is it fixed?
First tell the machine the board length, width and thickness; set the rails to the board width; when the board comes in, the stopper stops it, then the board edge is clamped, pins or support blocks push up from below, and a hold-down presses from above. If this step is not done well, every placement height after it is off.
The first thing the machine does not know is how big the board is. The three numbers of length, width and thickness decide how wide to open the rails, how high the support below must push, and at what height the board surface sits. For the YSM20R in single-lane mode, the website gives boards from L50 × W50 mm to L810 × W490 mm; with the dual stage (an option for the X-axis dual beam, and for nothing else) carrying two boards at once, each board is up to L380 × W490 mm.
Table 2. After the board comes in, what each step protects
| Step | What to tell the machine / adjust | What happens if it is not done well | Related part |
|---|---|---|---|
| Rail width | Adjust to board width | Too loose: the board runs skewed and stops inaccurately; too tight: the board jams | Rail conveyor wheel |
| Stop (stopper) | The board stops at the placement position | An aged stopper makes the stop position unstable and repeatability worse | Stopper plate |
| Edge clamp | Clamp the board edge | A worn clamp piece does not hold; the board moves slightly during placement and parts are off position, obvious on thin boards | Rail edge-clamp triangle piece |
| Support | Pins or support blocks push the board flat from below | If it is not flat, the board surface height is wrong, and so is the placement height | PCB support aluminum block, support pins and bases |
| Board thickness | Decides support lift and board surface height | Wrong entry means the height of the whole board is wrong | — |
“What happens if it is not done well” is taken from the wear notes on Jiahon’s rail and support part pages and from field experience; this is the general case, and individual cases still vary.
This section is easy to underrate. Q06 explains the reason more clearly: the machine’s eye can see offsets on the plane, but it cannot see local highs and lows of the board. For the placement height to be accurate, the board must be held flat within what the machine allows — so pins and support blocks must do more than “touch”: every one must be the same height. Take Jiahon’s PCB support aluminum block as an example (the product page lists YG12, YV100XG, YS12, YS24, YSM10, YSM20): the heights are fixed values of 76, 66 and 64 mm, and the length is 20 to 500 mm; when you change part number, measure the height of the existing support block first, then choose the length.
A board that passes at the board maker may not be one the machine can take
There are two yardsticks for board warp. The board maker ships by IPC-6012: for boards with surface-mount parts, bow and twist are limited to 0.75%. For bow, along the 250 mm long side of a board:
250 mm × 0.75% = 1.875 mm (bow, along the long side)
IPC-6012: 0.75% for boards with surface-mount parts, 1.5% for other boards; the method follows IPC-TM-650 2.4.22: bow is calculated from the board length and width, and twist is calculated separately from the diagonal.
How much the mounter accepts depends on the tolerance in the maker’s manual, and on some machines the upward and downward limits are specified separately. Get both numbers and compare: where the board maker passes it and the machine cannot take it, you make up the gap with extra support or a carrier. For how to measure board warp and carrier warp, see White-light structured-light thickness and deformation measurement: non-contact inspection of carrier warp, board warp and solder paste thickness.
› Related products: Rail edge-clamp triangle piece, stopper plate and rail conveyor wheel, fitting Yamaha, Feeder calibration bar, PCB support aluminum block and feeder guide rail, fitting Yamaha, PCB support pins and bases (multi-brand)
Q 03. Why must fiducial marks be on the diagonal? What does each of the three levels cover?
When the board turns through a small angle, the farther apart two marks are, the larger the relative shift measured, and the easier it is to tell apart from measurement error; the diagonal is the longest distance that can be drawn on the board. On a 250 × 200 mm board, with the marks on the diagonal, the signal is 6.1 times that of marks just 50 mm apart. Use Board for the whole board, Block for panel pieces, and Local for special or high-value ICs.
With the board clamped, the machine still does not know where to place the parts: the board may sit a little off or turned on the rails, and the board material itself expands and shrinks. The machine uses the mark camera on the head to look at the fiducial marks on the board, compares the actual positions with the coordinates in the program, and then corrects all placement positions together.
Why the diagonal
When the board turns through a small angle θ, the relative position between two marks differs by “distance between the two points × θ”. The camera’s own measurement error is fixed, so the farther apart the two points are, the larger the signal, and the easier it is to see through the error. Take a 250 × 200 mm board as the worked example, with each mark 5 mm from a board corner:

Figure 2. For the same turning angle, the longer the distance between two points, the larger the relative shift. Left: marks on the diagonal, versus marks placed just 50 mm apart. Right: shift = distance × θ (angle exaggerated for illustration; the arc length ratio is true).
Two marks: (5, 5) and (245, 195); X difference 240 mm, Y difference 190 mm
Diagonal distance = √(240² + 190²) = √(57,600 + 36,100) = √93,700 = 306.1 mm
Assume the board turned 0.05°: 0.05 × π ÷ 180 = 0.000873 rad
Relative shift with the diagonal layout = 306.1 × 0.000873 = 0.267 mm
With marks just 50 mm apart = 50 × 0.000873 = 0.044 mm
306.1 ÷ 50 = 6.1 times
The board size and 0.05° are assumed values for illustration, not the specification of any machine or board material.
The same reasoning explains another thing: when a board turns, the corners far from the center of rotation always shift the most. Marks on the diagonal measure exactly the places that will shift.
Two marks on the diagonal are the basic layout for the machine to correct translation and rotation; to also correct stretch and distortion that differ in the two directions, at least three are needed (SMEMA 3.1, Fiducial Mark Standard). Board makers’ design advice is also to place three, as close to the corners as possible and spread apart, and the extra one lets the machine also determine the board’s orientation (Eurocircuits, “Finding fiducials”). Whether to place two or three depends on the correction methods the machine supports and on the board design.
Three levels: Board, Block, Local
Table 3. The three levels of fiducial marks
| Level | What it covers | When to use it |
|---|---|---|
| Board fiducial | Position, rotation and stretch of the whole board | Needed on every board; two on the diagonal |
| Block fiducial | Each small piece of a panel is corrected separately | Panels, when the position between pieces differs |
| Local fiducial | Local correction for one part or a small area | Special or high-value ICs such as fine-pitch QFP and BGA; local stretch on large boards |
Some machines divide the Local level more finely (correct one placement point, or several points in an area together); names and settings follow each maker’s manual.
A regret often seen on site is stopping after the whole-board level. The position differences between panel pieces and local stretch around fine-pitch ICs cannot be corrected by the Board fiducial; when yield is stuck on certain parts or positions, it is often worth going back to check whether the two lower levels were done.
When a mark is not recognized steadily, it is mostly not the camera’s fault but a mismatch between the mark’s surface and the lighting: shiny copper, matte copper and surface-treated copper all reflect differently, so the machine’s light (coaxial, ring or infrared) must be adjusted accordingly. What the design side can do first: use a solid round mark with an exposed-copper diameter of about 1–2 mm, with a clear zone around it 2–3 times the exposed-copper diameter (SMEMA 3.1 specifies a diameter of 1–3 mm and a clear zone radius of at least 2 times the mark radius; Eurocircuits, following IPC-7351B, suggests 1:2 to 1:3); we also suggest the same surface finish for the marks on the whole board. These are decided at the PCB design stage.
Q 04. Where is point A? Feeder station number and feeders
Point A is the station number: it tells the machine at which station this part sits, so the head knows where to pick. Tape parts use tape feeders, large ICs use trays, and parts in tubes use stick feeders; when picking is unstable, parts are skipped, or the machine stops, check the feeder itself first.
The machine does not know at which station a part sits; the station number is entered in the part data. For tape feeders the pick position can be worked out from the station number; for trays the pick point has to be taught (see Q10). The YSM20R website gives the number of part types that can be set as: fixed feeder base up to 140, exchange-cart type up to 128 (both counted in 8 mm tape); for trays, an sATS30 (up to 30 types) or cATS10 (up to 10 types) is added.
Point A looks simple, yet is a common source of stops: if a feeder is not seated, the machine stops on an interlock; feeding that does not reach position, skips a pitch or has a loose cover becomes pick failure and thrown parts.
Table 4. Three kinds of point A, and where each often goes wrong
| Supply method | How point A is set | Common problems | Related parts |
|---|---|---|---|
| Tape | Pick position worked out from the station number | Worn ratchet or spring jams the feed; a worn cover-tape cutting edge tears the cover tape; dust on the optical-fibre sensing head causes false action | ZS / SS / CL feeder parts; ZSR / ZSS safety latch, spring and handle |
| Tray | Teach points on the tray pockets (see Q10) | Taught on the part rather than on the pocket; pocket bottom height not uniform | Antistatic tray |
| Stick | Discharge position at the stick mouth | Part stuck at the stick mouth; vibration does not feed; dust on the sensor | SS / CL stick feeder parts |
The tape and stick rows are taken from the wear notes on Jiahon’s feeder part pages; for the tray row, see Q10; this is the general case, and individual cases still vary.
When the cover-pressing latch on a ZSR-series feeder wears, the press cover easily loosens, which is one common cause of unexplained pick failures; when the feeder guide rail wears, insertion resistance rises and positioning is unstable, and feeders falling off after a big line changeover often start here. Splicing is also part of point A: if the splice is crooked, the tape jams and skips in the feeder.
The optional ALF auto-loading feeder of the YSM20R is described on the website as having a central opening, so you do not tear open the cover tape or splice; with this kind of feeder the focus moves from “is the splice good” to “has the reel loaded into position”.
For step-by-step checking of poor feeding, see Poor feeder feeding and jams: five places to check in order, from the press cover to the bird’s beak; for looking at the nozzle, feeder and drive sections together, see From nozzle to feeder: the core of “precise pick and place” that Jiahon builds for SMT mounting.
› Related products: YAMAHA mounter feeders, ZS / SS / CL feeder parts, fitting Yamaha, ZSR / ZSS feeder safety latch, spring and handle set, fitting Yamaha, SS / CL stick feeder parts, fitting Yamaha, SMT splicing pliers
Q 05. The machine does not know what this is: what must part data tell it? How do you choose a nozzle?
After a part is picked up, the machine does not know what it is. You tell it the length, width and height; for leaded parts, also lead count, pitch and lead width; and the part type, which nozzle to use, and the package. The machine compares these numbers with the image the camera sees, and uses the thickness to work out the placement height.
“Telling it length, width and height” can be done two ways: measure with calipers and enter by hand, or bring in a similar entry from the part library and fine-tune. By hand is slow but any part can be created; the library is fast but its coverage is limited, and after bringing one in, fields such as lighting and feeder type often need changing. If the lead pitch and lead width are not measured accurately at first, it does not matter, because they can be corrected in the next step, recognition adjustment (Q06); thickness is different, since it is directly tied to the placement height and must be measured accurately. The YSM20R website also says that recognition data for odd-shaped parts can be generated automatically.
Table 5. What the machine does with each number in the part data
| What you tell it | What the machine uses it for | What happens if entered wrong |
|---|---|---|
| Length, width | Matches the outline during recognition; decides which camera to use | Recognition fails, or the orientation is misjudged |
| Height (thickness) | Works out the placement height; tall parts need a different camera | Placed too deep, crushing the part or squeezing the solder paste; placed too shallow, the part drops and shifts |
| Lead count, pitch, width | Finds the leads during recognition and judges whether any are bent | Leads not found, so the part is thrown away |
| Type | Decides the recognition method (chip, SOT, SOP, QFP, BGA…) | Wrong method, unstable recognition |
| Nozzle | Picks the part | Weak hold, or touches the neighbouring part |
| Package | Back to ④: tape, tray or stick | Wrong feeder type |
The wide-view scanning camera on the YSM20R HM head can recognize parts from 0201 to 12 × 12 mm; parts 6.5 mm or more in height, or 12 mm or more in length and width, need the optional multi-function camera (Yamaha website and the 2018-01-11 news release).
Choosing a nozzle: look for a standard one first, then talk about custom
Nozzles are chosen by part shape: a small chip uses a small bore, SOP and QFP use a large bore; when parts on the board are packed close, the nozzle outline also must not touch the neighbouring parts. The design concept of the YSM20R is the “1-head solution”: the website says the HM head, a single head type, covers more than 90% of part sizes (the maker’s own statistic), so no head change is needed during production — what you change is the nozzle. So nozzle part-number management comes up more often than head type.
If a standard part number can be found, use the standard product first: Jiahon’s pages Yamaha-fit nozzles and Yamaha-fit nozzles II list the part numbers, and the models the page lists are YS12, YS24, YSM20, YG200 and YG300; for the YSM20R, please send the model and the nozzle code, and we first confirm whether it matches. For parts a standard nozzle cannot hold steadily — odd-shaped connectors, heat sinks, large SOP / QFN, parts with no place to pick on the top surface — use nozzle customization (odd-shaped nozzles): provide samples and drawings, Jiahon designs from the machine and part geometry, makes one trial piece for a test on the machine, and goes to volume after it passes; whether it can be made depends on the model and the part, and for a model not listed on the page, please call to confirm first.
For choosing among the maker’s own, fit-type and custom routes, see How to choose an SMT nozzle? Maker’s own vs fit-type vs custom, explained at once; for parts taller than the board with no place to pick on the top surface, see The part is taller than the board: where should the nozzle pick? The upper and lower limits of tip size, explained; for parts bigger than a palm and heavier than a phone, see A part bigger than your palm and heavier than a phone: can the mounter pick it up? The four gates of large-part pick and place, and nozzle selection. Nozzle part numbers of each brand can be looked up in the SMT nozzle overview.
› Related products: Yamaha-fit nozzles (YS12 / YS24 / YSM20 / YG200 / YG300), Yamaha-fit nozzles II, nozzle customization (odd-shaped nozzles), SMT nozzle overview
Q 06. How does the machine’s eye recognize a part? Why is XY measured on every part, while Z relies on consistency?
The machine finds position with one sense, the camera, used in two directions: looking down at the marks on the board (③) and looking up at the part on the nozzle (⑥). Offset and angle on the plane are measured and corrected for every board and every part; under normal settings, height is not measured on every part, and relies on the dimensions of pins, supports, trays and nozzles being consistent.

Figure 3. One pair of eyes, two directions. Looking down at the marks and up at the part: shifts on the plane are measured and corrected; if the board sinks a little, the eye cannot see it (schematic).
At the moment a part is picked up, it is rarely exactly at the center of the nozzle: the tape pocket has clearance, the nozzle has tolerance, and the part swings at the instant of pick. The camera looks at the underside of the part from below, measures how far it is off the nozzle and by how many degrees it is turned, and the machine corrects for it when placing. That is why X, Y and angle can be corrected for every part separately — every part is measured and then corrected, a closed loop.
The YSM20R HM head carries a wide-view scanning camera; the website says it recognizes parts from 0201 to 12 × 12 mm, and does so on the straight path from pick to place while moving (flying recognition), without spending separate recognition time; with side lighting added, the solder balls of CSP and BGA can also be recognized at high speed. Parts larger or taller than that (6.5 mm or more in height, or 12 mm or more in length and width) use the optional multi-function camera, and the head carries the part over the camera to be recognized.
Table 6. What is seen and what is not
| Direction | Who measures | How often | What can be corrected | What it relies on when it cannot correct |
|---|---|---|---|---|
| Looking down at the board | Mark camera | Every board | Board position, rotation, stretch | Marks must be recognized steadily: surface, lighting, design |
| Looking up at the part | Scanning camera, multi-function camera | Every part | Part offset and angle on the nozzle | If it is off too far, the part is not held or not in the frame |
| Height Z | Under normal settings, not measured on every part | Set value plus taught points | Fixed deviations (taught points, auto calibration) | Every pin, every pocket and every board being the same |
The YSM20R website lists “automatic calibration and teaching of pick position and pick height”. Teaching and auto calibration make up for fixed deviations; differences between one pin and the next, or one pocket and the next, still depend on the consistency of the parts themselves.
You can remember it in one sentence: XY is measured on every part, Z relies on consistency. For peripheral parts the meaning is direct: things that affect height — pins, support blocks, carriers, tray pocket bottoms, nozzle length — need to be consistent; things that affect plane position but that the camera will correct — tape feed position, tray pocket position — matter just so far as the offset must not be so large that the part is not held or not in the frame.
When recognition fails, first tell apart “did not see it clearly” from “what it sees is not that part”: an image that is too dark or too bright is a lighting problem; a pick that is not at the center is a pick-position problem; wrong outline parameters mean going back to ⑤ to re-measure and re-enter. A dirty or worn nozzle changes the reflection and outline of its end face and makes recognition unstable too — for how to tell, when a part is thrown away, whether the nozzle is dirty, worn, or the problem is not the nozzle at all, see Nozzle pick failure and thrown parts: first judge whether it is dirty, worn, or not a nozzle problem at all.
Q 07. Where to place: where do X, Y and R come from? Why should the part follow the solder paste?
X and Y are the coordinates measured from the board origin to the part center, and R is the angle the part is to turn; after entering them, confirm by teaching points with the camera, and teach them with mark correction active. The coordinates come from Gerber, but a part must in the end sit on solder paste — follow the paste, do not hold rigidly to the pad.
The machine’s last “does not know” is where to place. Every part has a set of X, Y (measured from the board origin to the part center) and an angle R. If R is not changed, the part is placed at the angle it had in the tape; if R is entered as 90, the nozzle turns the part 90 degrees first and then places it. Coordinates are mostly brought in from the CAD or Gerber part-center file, then spot-checked with the camera, and doubtful ones are taught one by one.
There is a detail that is easy to overlook in teaching: teach with mark correction active. The board itself stretches and turns; if you do not teach in the corrected coordinate system, the taught points are right just for this one board. Also, coordinates are best taught last — if you teach before the board is clamped firmly and the marks are recognized steadily, then whenever anything is changed afterwards, the points taught earlier must be redone.
Gerber gives the center, but the part should follow the paste

Figure 4. When the paste is printed off position: placing by the pad versus following the paste. When both ends sit on paste, the surface tension of molten solder in reflow pulls the part back onto the pad (schematic).
The board maker’s boards made from Gerber have deviation, and the stencil apertures have tolerance; of the three, just the mounter’s program is written precisely from Gerber — provided the machine is calibrated, the offset is near the center value, and the dimensional error of the part itself is accounted for. The trouble comes when the paste is printed off position: if the part is placed at the pad coordinates, one end may not sit fully on paste, the forces on the two ends in reflow are uneven, and tombstoning and open joints often start that way.
If the part is placed at the position where the paste was actually printed, with both ends on paste, the surface tension of the molten solder in reflow pulls it back onto the pad, which is called self-alignment. Academic research also says that, when placing passive parts, considering paste volume and offset together can lower the chance of tombstoning and of parts landing off the pad (Parviziomran et al., 2019, in Procedia Manufacturing). But following the paste merely stops the bleeding; why printing is off must be traced back to the printing side and its consumables — do not move the mounter’s program coordinates further and further from Gerber; for the method, see Solder paste print defects: working back from how the print looks to which consumable to change.
One more thing to look at together in reflow: tall parts cast a shadow on smaller BGA and CSP beside them, local temperature cannot rise, and head-in-pillow (HIP) may appear. This kind of problem has to be dealt with through part layout and the reflow profile together.
Look at the first article after placing
First-article defects fall roughly into three kinds: position shift, part placed at the wrong position, and wrong angle. For a shift, check ③ marks, ⑦ taught points and ⑥ recognition; for a wrong position, check coordinate entry or the block offset of a panel; for a wrong angle, check the R value and the tape direction. Checking a first article by hand against the BOM and coordinates takes a long time; the SMT first-article inspection machine JHFAIS-G2 can import the BOM and coordinates and check part by part for wrong parts, missing parts, reversed parts and angles.
If the shift was not there from the start but grows the more you run, look at the machine itself: accumulated servo motor encoder error makes positioning drift slowly; wear in the head’s θ-axis mechanism makes the angle go off. Also, when the X-axis drag chain (cable carrier) ages, cables and air hoses are damaged by repeated bending, causing on-and-off signals or air-path faults; Jiahon’s drag chain page lists the YSM20R X-axis drag chain as a new part number (KMK-M2267-00X), different from the old one for the YSM10 / YSM20, so confirm the model before buying.
› Related products: Servo motors for Yamaha mounters (YS12 / YS24 / YSM20), Servo motors for Yamaha mounters II, Yamaha Unit series (head module), SMT mounter cable carrier / drag chain, SMT first-article inspection machine JHFAIS-G2
Q 08. How fast, how slow: which speed, dwell, height and vacuum threshold settings do you adjust?
Picking and placing each have a set: Z-axis descent and rise speed, XY travel speed, dwell time, height correction, and vacuum judgement threshold. Small parts can run at full speed; for large, heavy or tall parts, slowing down and adding a little dwell time is often more effective than adding suction.
With the main idea told, what remains is detail: how fast and how slow to place, and how fast and how slow to pick. Field names differ from machine to machine, but they all come down to the five things below:
Table 7. Five things in “how fast, how slow”
| Parameter | When picking | When placing | When to touch it |
|---|---|---|---|
| Z speed | Nozzle descends, rises | Same | Slow down for large, heavy, tall parts; slow down for thin, fragile parts |
| XY speed | Move to the feeder | Move to the board | A large part rides on the nozzle by friction, and too much acceleration throws it off |
| Dwell time | Hold a moment after the part is held, then rise | Hold a moment after placing, then leave | Parts whose vacuum builds slowly; parts that need time for the paste to take them |
| Height correction | Pick height | Place height | When part thickness, tape, tray pocket bottom or nozzle length has a fixed difference |
| Vacuum judgement | Confirm the part is held | Confirm it has been released | Threshold is set per part; a leaking nozzle narrows the gap between part and no part and causes misjudgment |
This is the general case, and individual cases still vary; parameter names and ranges follow the maker’s manual.
The reasoning for large, heavy parts is worked out in A part bigger than your palm and heavier than a phone: can the mounter pick it up? The four gates of large-part pick and place, and nozzle selection: while moving, the part rides along with the nozzle by friction, and at the same acceleration the holding force needed is higher than at the instant of lifting. So for large parts, slowing down is often far more worthwhile than straining to enlarge the suction area.
On the vacuum side, what is often seen on site is not a wrong setting but a dirty nozzle and vacuum path: dirt in the nozzle bore, a blocked filter element, or a leaking seal ring on the nozzle holder all weaken vacuum and blur the difference between part and no part. The YSM20R website lists the nozzle health check as a self-monitoring maintenance function — the machine watches the state for you, but someone still has to do the cleaning and replacing. For nozzle cleaning, lubrication, and when to change the vacuum valve core, see From nozzle cleaning to lubrication: the long-term stability Jiahon builds for SMT mounting.
For the machine to be stable, the air supply must be stable too. The air supply condition on Yamaha’s website is 0.45 MPa or more, clean and dry; the air filter and pressure regulator on the facilities side are the first gate for that sentence. While learning, turn the whole machine’s speed down and watch each motion clearly; adjust it back for volume production.
› Related products: P4 fully automatic nozzle cleaner JHPBT-40 / 60S / 80, Lubrication and maintenance spare parts for Yamaha mounters (YG · YSM), SMC air filter element, SMC AR50-10BG-B pressure regulator
Q 09. The catalog says 95,000 CPH; where does the cycle time on site come from?
95,000 CPH is the figure under Yamaha’s defined ideal conditions (X-axis dual beam, two HM heads). The cycle time on site depends on the program: whether the panel is expanded, whether it is optimized, how many times nozzles are changed, how far the feeders are from the board, and whether several nozzle axes can pick together and place together.
Once the eight questions are answered, the program can run; making it run fast is another matter. The 95,000 CPH in the catalog is, as the website notes, the placement capacity with an X-axis dual beam, two HM heads and the maker’s ideal conditions. Your board, your parts and your program decide how fast it really runs.
Table 8. Where the time goes, and how to change the program
| Where the time goes | How to change the program |
|---|---|
| Panel pieces placed one block after another | Expand the blocks into the whole board, then optimize |
| Changing nozzles all the time | Line up the parts that one nozzle can pick; change the multiple nozzle axes beforehand |
| The head travels a long way | Put commonly used feeders at stations closer to the board |
| One nozzle picks one part and goes | Several nozzle axes pick several parts at once, recognize together, and place together |
| Optimization changed stations but feeders were not moved | Actually move the feeders to the new station numbers, otherwise the wrong parts are placed |
Two reminders: once optimization is done it usually cannot be undone, so always save a backup copy before doing it; for a program that has already been expanded and optimized, after you add parts you must expand and optimize again.
How big the gap between catalog CPH and cycle time on site is, and how to estimate it, is covered in a full article from Jiahon’s knowledge base: The speed on the catalog is not your speed.
Q 10. When point A is a tray, what needs extra attention?
Teach the tray pick point on the pocket, not on the part — a part moves in its pocket, the pocket does not. For pocket pitch, teach the first pocket and the diagonal last pocket together; the pocket bottom height is the pick height, and one value is usually used for the whole tray, so every pocket bottom must be the same height.

Figure 5. Two key points for tray parts: teach the point on the pocket; the pocket bottom height must be consistent (schematic).
Large ICs such as QFP and BGA mostly come in trays. When the tray is put on the tray rack, align a corner of the tray with the origin of the rack; teach the pick point on the pocket: use the same position in the first pocket and in the diagonal last pocket, so the machine works out the pocket pitch itself, then confirm pocket by pocket that the camera follows the pocket. The reasoning for the diagonal is the same as in Q03 — the longer the distance, the more easily the accumulated pitch error is caught.
This comes back to the sentence in Q06: XY is measured on every part, Z relies on consistency. If a part sits a little off in its pocket, the camera corrects it; if the pocket bottoms differ in height, the machine does not know. The flatness of the tray, the height of each pocket bottom, and the clearance between pocket and part are the specifications a tray should keep — the clearance must be smaller than the offset the nozzle can tolerate.
A standard tray is judged by the JEDEC outline, not by the equipment brand; if a standard tray has too little inner height or cannot hold the sides, change it structurally. Three related articles: How to choose semiconductor totes and antistatic trays: three layers of protection, JEDEC tray sizes and docking with automation, Tray specification does not match, inner height not enough? Jiahon offers custom design improvements, Is the mold fee sky-high? A new design held hostage? Antistatic trays with shared molds, order small quantities directly.
Tray parts are mostly moisture-sensitive; the exposure time after opening and baking must be managed together, see What is a moisture-sensitive part’s MSL? J-STD-033 packaging, exposure time and baking in one article.
› Related products: Antistatic trays, Smart programmable oven JHSXH-480
Q 11. Misplaced, or thrown away: which question do you check first?
First tell apart whether the whole board is off, just certain parts are off, or it gets worse the longer it runs. A whole board off in one direction: look at ③ marks and ⑦ taught points; just certain parts off: look at ⑤ part data and ⑥ recognition; getting worse as it runs: look at the machine itself. Once you map it to the eight questions, you know whether to change the program or replace a part.
Table 9. Symptoms on site, and which question to check first
| Symptom | Check first | What to check | Parts that may need replacing |
|---|---|---|---|
| Whole board off a little in the same direction | ③ alignment, ⑦ coordinates | Whether the marks are recognized steadily; whether points were taught under mark correction | — (mostly the program) |
| Just certain parts off, angle off | ⑤ part data, ⑥ recognition | Outline parameters, lighting, recognition adjustment; nozzle dirt or wear | Yamaha-fit nozzles; Unit series (θ-axis mechanism) |
| Placed at a completely different position | ⑦ coordinates, ③ panel | Coordinate entry, block offset of a panel | — |
| Gets worse the longer it runs | The machine itself | Motor encoder, lubrication | Servo motors; lubrication and maintenance spare parts |
| Thrown parts, insufficient vacuum | ⑧ vacuum | Nozzle bore, filter element, nozzle holder seal ring | Nozzle cleaner; filter element; Unit series |
| Pick failure, skipped parts, feeder stops | ④ point A | Whether the feeder is seated; feed mechanism, press cover, guide rail | ZS / SS / CL feeder parts; ZSR / ZSS safety latch and spring; feeder guide rail |
| Board lifts, bounces when tapped; thin board shifts | ② fixing | Board thickness setting, support position, edge-clamp piece, stopper | PCB support aluminum block; rail edge-clamp triangle piece and stopper plate |
| Tombstoning, open joints | ⑦ plus printing | Whether the paste is printed off position; whether the part sits on the paste | — (check printing first) |
| A fixed error code after power-on that restart cannot clear; one sensor signal always abnormal | The machine itself | Control board, sensors | Control board |
This is the general case, and individual cases still vary; for the actual fix follow the maker’s manual and the instructions of the error message. The models each part fits follow what each product page lists.
“Check first” in the table is an order, not a conclusion. A whole board off in the same direction is mostly checked from the program and alignment first; but if the same shift grows week by week, stop changing the program — that is the machine telling you some part needs to be replaced.
Q 12. If you want Jiahon to make nozzles, supports or trays, what data should you prepare?
State the model and head type first (for example YSM20R, HM head), then give data for what is to be made: for a nozzle, the part specification or a sample, a bottom view and a photo of the top surface; for a support, the board size, thickness, warp direction and the height of the support now in use; for a tray, the part size and weight, and whether it must follow the JEDEC outline.
These eight questions are also the starting point when we design peripheral parts: first ask which question the part falls on, then ask whether the eye measures it on every part for that question — if yes, the offset just must not be so large that the part is not held or not in the frame; if no, it must be made consistent. The table below shows three kinds we are often asked about:
Table 10. Data to prepare when asking Jiahon to make peripheral parts
| What to make | Which question it falls on | Please prepare | Why these are needed |
|---|---|---|---|
| Custom nozzle | ⑤ ⑥ ⑧ | Model and head type; part datasheet or sample; bottom view or photo of the underside; photo of the area that can be picked on the top surface; whether automatic nozzle change is needed | The outline must not touch adjacent nozzles and parts; the end face must avoid heat sinks, capacitors and labels; length must be consistent for the height to hold |
| Board support (support block), pins | ② | Model; board size and thickness; warp direction (convex or concave); positions of parts on the underside; height of the support now used | Support points must avoid underside parts; the height must match the machine’s original support height |
| Tray (standard or custom) | ④ ⑤ | Part size and weight; quantity; whether it must follow the JEDEC outline; whether it must be antistatic | Pocket bottom height consistent; clearance between pocket and part smaller than the offset the nozzle can tolerate |
Physical items sent to Jiahon can be arranged for a trial pick and measurement; custom items are quoted after evaluation of the actual part. This is the general case, and individual cases still vary.
For machines other than the YSM20R, ask the same eight questions: Panasonic, FUJI and JUKI use different screen names, but the questions do not change. For parts for each brand, see the two general categories Mounter-related (all brands) and YAMAHA mounter parts.
Need help judging?
Tell us your machine and parts, and let Jiahon map them to the eight questions
Tell us the model and head type, the part size or a sample, and which step you are stuck on — misplacement, thrown parts, machine stops, or a new part that cannot go on the line. We first map it to which of the eight questions it falls on, then explain whether the program should be adjusted or a part replaced; if you need a custom nozzle, support or tray, send the actual item to Jiahon and we can arrange a trial pick and measurement.
Yamaha-fit nozzles YS12 / YS24 / YSM20 / YG200 / YG300: part number list
Nozzle customization (odd-shaped nozzles): provide samples and drawings, one piece made for a trial on the machine
YAMAHA mounter feeders: feeders and feeder parts
Rail edge-clamp triangle piece and stopper plate, fitting Yamaha: maintenance parts for boards that are not clamped firmly or stop inaccurately
PCB support aluminum block, fitting Yamaha: heights 76 / 66 / 64 mm, length 20–500 mm
Servo motors for Yamaha mounters: XY axes and each axis of the head
P4 fully automatic nozzle cleaner: cleaning dirt in the nozzle bore
SMT first-article inspection machine JHFAIS-G2: import the BOM and coordinates to check the first article
SMT nozzle overview: quick lookup by brand × machine × nozzle part number
YAMAHA mounter parts: all Yamaha mounter parts
Sources and notes
Yamaha Motor website YSM20R product page (Yamaha Motor | YSM20R Overview) and specification page (Yamaha Motor | YSM20R Specifications, External dimension), viewed 2026-09-30; Yamaha Motor news release (2018-01-11), “Announcing High-end High-efficiency Modular Z:LEX YSM20R”. The YSM20R specifications and functions in the article are all quoted from these public sources.
Board bow and twist: the limit follows IPC-6012, Qualification and Performance Specification for Rigid Printed Boards; the method and formula follow the public IPC test method IPC-TM-650 2.4.22 Rev. C, “Bow and Twist (Percentage)”; for a board maker’s summary see Eurocircuits, “Bow and Twist on a PCB”.
Fiducial marks: shape, diameter, clear zone and number follow SMEMA Standard 3.1, Fiducial Mark Standard; for clear-zone ratio and layout advice see also Eurocircuits, “Finding fiducials” (citing IPC-7351B).
Self-alignment and placement offset: Parviziomran, I., Cao, S., Yang, H., Park, S., Won, D., “Optimization of Passive Chip Components Placement with Self-Alignment Effect for Advanced Surface Mounting Technology”, Procedia Manufacturing, vol. 39, pp. 202–209 (2019; paper of the 25th International Conference on Production Research, ICPR, open access), DOI 10.1016/j.promfg.2020.01.313.
The operating logic in this article is the Jiahon affiliated company Engineering Department’s summary of learning mounter programming, plus field experience, written in its own words; it does not quote or reproduce text, pictures or operating steps of the maker’s manual. Screen names and actual operation follow the maker’s manual and the maker’s training. The YSM20R is listed as discontinued; please confirm with the maker whether its successor is operated the same way.
The worked examples for the diagonal and for bow use assumed values (board size, marks 5 mm from the corner, turn angle 0.05°), not the specification of any machine or board material.
The models that Jiahon products in the article fit follow what each product page lists; “fit” means supplied items matching in size and specification, not parts from the equipment maker. The Jiahon affiliated company does not sell or act as agent for any brand of mounter. Yamaha and Z:LEX are trademarks of Yamaha Motor Co., Ltd.; this article uses them just to describe the model.
This describes the general case, and individual cases still vary.